Convoy M1 quad
I use a custom machined pill,clear narrow optic and a fet+ 7135 driver running guppydrv2 firmware. They will put out 3400+ lumens at start up on a high discharge unprotected 18650 cell Fet+ 7135 driver and the new Samsung 351 5700k emitters in these. They are completely user programable using guppydrv2 firmware with 24 different mode groups to choose from. They have thermal regulations and low voltage detection built in. All of my lights come with glow in the dark center rings. Colored tail boots are a add on option and are available in GID green, blue, red, and orange.
This firmware allows the ultimate in user customizability, with 22 built-in mode groups, that the user can select via a series of button presses and a user programmable turbo timer that will automatically step the power down to 50% after the set time is hit (see below for instructions).
Low voltage protection: With 1S cells (non-zener mod) the light will begin to step down output at around 2.8v under load. The light will not shut completely off, but will continue to run at a moonlight level.
ONLY USE HIGH DISCHARGE UNPROTECTED (1) 18650 . SILVER THREADS OF THE BATTERY TUBE FACE THE HEAD OF THE LIGHT.
None other than Dr.Jones Guppy2drv. The ultimate in flexibility. This UI offers a wide range of modes to choose from. Something for almost any occasion.
User Selectable Groups:
1. 1% - 25% - 100% | Memory
2. 1% - 25% - 100% | No Memory
3. 100% - 25% - 1% | No Memory
4. 1% - 25% - 100% - Strobe | No Memory
5. 1% - 25% - 100% - Strobe | Memory
6. 10% - 100% | Memory
7. 10% - 100% | No Memory
8. 100% - 10% | No Memory
10. 100% - Strobe | No Memory
11. Strobe - 100% | No Memory
12. ML - 2% - 25% - 100% | Memory
13. ML - 2% - 25% - 100% - Strobe - Beacon | No Memory
14. ML - 100% | No Memory
15. 100% - ML | No Memory
16. ML - 100% | Memory
17. ML - 1% - 5% - 15% - 40% - 100% | Memory
18. ML - 1% - 5% - 15% - 40% - 100% | No Memory
19. 100% - 40% - 15% - 5% - 1% - ML | No Memory
20. 100% - 40% - 15% - 5% - 1% - ML | Memory
21. 1% - 5% - 15% - 40% - 100% | Memory
22. 1% - 5% - 15% - 40% - 100% | No Memory
23. 100% - 40% - 15% - 5% - 1% | No Memory
24. 100% - 40% - 15% - 5% - 1% | Memory
To switch mode groups: rapidly tap the switch 8 times, the light will then enter the programming mode and begin to flash. With the light in programming mode, tap the switch the same number of times as your desired mode group. The light will blink and your mode group will be memorized.
Example: To select mode group 3, tap the switch 8 times quickly to enter programming mode. As soon as the light enters programming mode and beings flashing, tap the switch three times. The light will blink to recognize the mode group change.
To set the turbo timer: rapidly tap the switch 8 times, the light will then enter the programming mode and begin to flash. With the light in programming mode, tap the switch 30 times to enter the turbo timer set mode. The light will then switch to 100% power. When the light is at the desired temperature for the turbo step down, turn the light off. The turbo timer will then be set. The turbo timer steps the light down to 50% regardless of the mode group set.